• Welcome back Guest!

    MARSH is a private reefing group. Comments and suggestions are encouraged, but please keep them positive and constructive. Negative threads, posts, or attacks will be removed from view and reviewed by the staff. Continually disruptive, argumentative, or flagrant rule breakers may be suspended or banned.

Recent content by RickD

  1. RickD

    I just changed my filter floss out last night and may still have some on the the floss. there...

    I just changed my filter floss out last night and may still have some on the the floss. there are typically several dozen. I can save the floss out. I just checked and there are still several that a nice and red, but curled up. I can bag them. Let me know.
    • RickD
    • Profile post
  2. RickD

    Where to buy Hanna phosphate Reagent

    Any know of a LFS selling phosphate reagent? HI713?
  3. RickD

    Having a 3D printer

    Yes, with some limitations. Get with me DM to discuss.
  4. RickD

    E-Marco

    I layered super glue (liquid) combined with reef sand then you can emarco and shape it the way you want. Superglue was very strong like the mortar. Phamily94 showed me his technique and his tank is full of long shelves.
  5. RickD

    Having a 3D printer

    spelling…nylon bolts
  6. RickD

    Having a 3D printer

    Depending on your slicer settings, the tolerance is fine. If they are tight, you can use a tap/die, but it’s not needed. The bolts will snap with too much force because printed along the thread. You can use my long bolts and it will work better.
  7. RickD

    Identification Shrimp-like

    That was my first thought. Thanks.
  8. RickD

    Identification Shrimp-like

    Cleaning out my floss and noticed this little creature. This is the best image I can get. It looked like a shrimp and what appeared to have claws. I thought it was only shrimp I have is cleaner and pistol. Any ideas?
  9. RickD

    Mixing different vendor two-part dosing

    I ran out of Fritz 2-part Liquid Calcium, instead of buying Fritz again, can I just mix my own (like BulkReef) and dose with that mix? I’m guessing yes, but want to be sure.
  10. RickD

    Having a 3D printer

    You get spoiled when you have a 3D printer to support my reef hobby.
  11. RickD

    Aquarium Grounding

    Same thing happened to me a week ago. I typically have towels on the ground to catch any spills, but this time I did not. I was shortest path to ground. My GFCI never tripped, but I got a nice jolt. I checked the stray current with my multimeter and pulled a plug one at a time - it was my...
  12. RickD

    Tank shut down cleaning questions??????

    This is how we clean the salt chlorinator for saltwater pools. Every 2-3 months it will leave calcium deposits on the electrodes and usually use 1:4 ratio. Vinegar is very weak. Just use goggles and be sure to mix downwind.
  13. RickD

    Reef Cleaners?

    I got an order from them last week. They had a lot in stock a few weeks ago, everything was good except I was disappointed with the amount of visible pods. They aren't known for that, but I tried to see what they can deliver.
  14. RickD

    The Floor Joist Headache

    I know it's an older post, but I've used and endoscope (link) in the past just to give me a start. Drill a small hole on one end then use that to get an idea how the joists are running. Not sure how it would hold in saltwater, but it is water proof and small enough that I though about using it...
  15. RickD

    What’s your current ATO and what will you buy next?

    In my old setup the direct method was leaving RO unit in a timer and it was directly connected to an ATO which was my top off. The doser was also tied into the timer so I would dose kalk into the reservoir. It went this method because I didn’t want my ATO, that was dosed with kalk, to be...
See more
Top