• Welcome back Guest!

    MARSH is a private reefing group. Comments and suggestions are encouraged, but please keep them positive and constructive. Negative threads, posts, or attacks will be removed from view and reviewed by the staff. Continually disruptive, argumentative, or flagrant rule breakers may be suspended or banned.

Search results

  1. A

    For Sale WTT - Hollywood Stunner Chalice (3x3" pieces)

    I have four pieces, 3x3 is a smaller average. Would call them all bigger than that. Looking for some Zoas or LPS, ideally relatively close to League City.
  2. A

    Tampa Bay Saltwater

    I might be interesting in a couple rocks for some diversity.
  3. A

    Waterbox 150.4

    First fish (yellowhead butterfly) added on Saturday, eating like a champ. Will give it a week or two before I start moving other fish over (yellow coris, melanurus, clown pair) Rock at this point is probably 50/50 new to live from my upgrade tank. Pods starting to establish a little bit...
  4. A

    Waterbox 150.4

    Space in these stands its fairly minimal. Between the hinges and the top off container I have about 5" to work with. So here is a prototype controller board (out of old presentation foam board) that I am pretty happy with. Tweaked a few things to make the switchboard sit back flush and am ready...
  5. A

    Waterbox 150.4

    These packaged tanks should really come with in cabinet lighting pre-installed. Either way, ill consider it a productive lunch break getting things lit up. I used these
  6. A

    Waterbox 150.4

    Dumb fake flower niche thing, yeet. Tank is in and wet! Only like 2 more days of water making to go. I really need to get a larger reservoir. Also, giving the Jebao gyre a shot. This thing is awesome so far, it can make some WAVES especially with only 8" of water in there.
  7. A

    Want to Buy Asterina Starfish

    I have a literal ton but Cypress to League City is quite a trek.
  8. A

    Waterbox 150.4

    I've had this thing for years (like, probably approaching 10) and never used it. I don't see a model number or anything on it, can anyone school me on how to use this in my sump? Or should I just get a new one?
  9. A

    Waterbox 150.4

    We'll see if this thread helps keeps me accountable, since Waterbox is already trying to do that by getting me a tank so dang quick. Decided to upgrade from my ~35 gallon Red Sea AIO (almost 10 years old) and was stuck between the Waterbox and ordering from Planet. Decided I didn't like the...
  10. A

    dosing

    What are you basing your dosing on when using AFR? Alk numbers?
  11. A

    All Things CNC!

    Work tank (12 gallon long) needs to be relocated due to new flooring install so I am planning to make a mobile stand for it instead of it being on my desk. Here is the shell so far!
  12. A

    All Things CNC!

    First cut success!
  13. A

    All Things CNC!

    Replaced upstairs floors last year and certainly couldn't let it go to waste. $100 in underlayment and some time, BAM, bougie garage floor.
  14. A

    All Things CNC!

    Its go time! *excuse the mess Getting a few things together and hopefully can run a few cuts tomorrow.
  15. A

    All Things CNC!

    For the equivalent to yours (use your laptop to control) but a 48x32” cut area is $2700 so not exceedingly more expensive but a lot more rigid. I went full bougee for right at $4k
  16. A

    All Things CNC!

    The X-Carve was my front runner for a long time and then I stumbled across Onefinity and it just felt right to me. They had some standard versions but right about the time I pulled the trigger they came out with a new "elite" series which just opened the door for pretty much every future upgrade...
  17. A

    Fishing pier tank theme

    Nice! I always looked at that one and never could pull the trigger for some reason, I ended up ordering a Onefinity. Is there a CNC thread somewhere? Might be worth making one if theres at least a few of us :)
  18. A

    Fishing pier tank theme

    One addition that would be neat and fit the theme are skilletfish. Should be around here although admittedly I haven't done enough collecting locally.
  19. A

    Fishing pier tank theme

    Well done. Looks awesome! Please report back on the grass when you make it out there. The picture reminds me of Vallisneria which I used to collect in brackish water in LA, don't think it would survive true marine but would be interested to know. The pinfish would certainly survive brackish...
  20. A

    Fishing pier tank theme

    Render looks super cool! I'm not so sure about using fresh poplar sap wood. Depending on the piece that stuff it soaked! Although with just macro and fish it might not be an issue. You might be better off finding some dimensional lumber "driftwood" and cutting that up. Still has some risk for...
Top