• Welcome back Guest!

    MARSH is a private reefing group. Comments and suggestions are encouraged, but please keep them positive and constructive. Negative threads, posts, or attacks will be removed from view and reviewed by the staff. Continually disruptive, argumentative, or flagrant rule breakers may be suspended or banned.

Search results

  1. Ranglin5o

    Robert's 210 no expenses spared build

    Yes the skimmer is the end of the line since it requires so much flow. I will be adding the bio reactor and media chambers to it as well and having the pump at about 85% (4000pgh flow) I'm adding apex flow monitors to each line so I can adjust the gate valves for flow.
  2. Ranglin5o

    Robert's 210 no expenses spared build

    Will be building the lower cabinet and finish that up this weekend! I have new parts I'm ordering this week.. Adaptive Reed Control Board to hang on the wall with Apex equipment Bashsea Bio-Reactor 8x30 Bashsea Media Reactor 6-18 x 2 (for carbon and gfo) Apex auto feeder Apex FMM for more...
  3. Ranglin5o

    Robert's 210 no expenses spared build

    My original 3150GPH pumps just wouldn't cut it and wasn't letting the tank cycle more then 600GPH at 100% and 400GPH on the manifold I got a new return and manifold pump installed last week. *Return - 5283GPH / Set at 70% and turning 1100GPH now *Manifold - 4755GPH / Set at 70% and flowing...
  4. Ranglin5o

    Robert's 210 no expenses spared build

    Well its long overdue but here is the current update on my build! Apex is setup and it has helped me keep everything in check! *FMM is hooked up to monitor my return line and skimmer GPH *Keeping the tank at 1100GPH cycling *Skimmer is turning 800GPH and has helped pull more junk out Have new...
  5. Ranglin5o

    Robert's 210 no expenses spared build

    Rodi 7 stage system. It ran in the tank for over a week being filtered without anything in it besides the dry rock and sand.
  6. Ranglin5o

    Robert's 210 no expenses spared build

    Mixxed in the sump little at a time and added calculated amount
  7. Ranglin5o

    Robert's 210 no expenses spared build

    Current today before a 40g water change bacause the high nitrate did worry me. pH - 8.1 Ammonia - 0 Nitrite - 2.0 Nitrate - 40/50ppm Salinity - 1.025
  8. Ranglin5o

    Robert's 210 no expenses spared build

    Wondering if I should do another full shot of ammonia in the tank to help... Wrong path or just wait?
  9. Ranglin5o

    Robert's 210 no expenses spared build

    UPDATE* So I used Brightwell's XLM and Quikstart to do my fishless cycle. It has been going right along with the instructions until today. I have a slight bit of confusion now that my NITRATE spiked up to 80ppm semi early. Ammonia dropped to 0 today NITRITE stayed at its 2.0 mark. Yesterday...
  10. Ranglin5o

    Robert's 210 no expenses spared build

    Intensity Spectrum Control Visual Spread
  11. Ranglin5o

    Robert's 210 no expenses spared build

    One other light that has caught my eye is the Zetlight company and they are Apex compatible!! Anyone seen/used them???
  12. Ranglin5o

    Robert's 210 no expenses spared build

    Well I've run into a snag and looking for a little advice on lights! I have it narrowed down to 4 different lights: Now I do have the EcoTech RMS rail already so all I need is one additional bracket to run the 4 XR15's I have read a lot of good things about the AP9X and that 2 could possibly...
  13. Ranglin5o

    Robert's 210 no expenses spared build

    Hear bad things about the razor x lights? BRS even did a full breakdown of the specs to set them too so thats why I was looking into them.
  14. Ranglin5o

    Robert's 210 no expenses spared build

    Initial tank setup completed!! Today the last parts to my return line came in! I'm running duel 1" RFG nozzles and they truly work like a charm! Please ignore the cloudy water! I leveled the sand again and disturbed it a little to much today.
  15. Ranglin5o

    Nem dying need help!!

    Green tip
  16. Ranglin5o

    Nem dying need help!!

    UPDATE: Green tip - Happy and healthy again! It decided it wanted to un-foot and walk all around the tank now, even got over the corner overflow wall and into the drain area! 4 new guys - Picked them up from a fellow member and they are all happy and healthy!
  17. Ranglin5o

    Robert's 210 no expenses spared build

    I used 3M Teflon fiber filled dope and 3M clear silicone mixed together for the threaded connections and I used regular Vaseline for the O-rings and threads for the disconnect couplers.
  18. Ranglin5o

    Robert's 210 no expenses spared build

    This weekend I got the drains and return lines 100% complete and leak free! The tank is up and running after a bit of tuning for the drain valves to get everything to quiet down a bit! I'm not sure this video will upload but I'm giving it a shot https://photos.app.goo.gl/4LNM3ca2vi4s81Et6
  19. Ranglin5o

    Robert's 210 no expenses spared build

    Drain and Return pumps took a bit of work but got everything setup leak free. NOTE: If anyone decided to use the Apex flow motoring 2" meter here are some helpful times that I found the hard way.. 1) USE PIPE DOPE AND SILICONE - I found a lot of stories after I had major leaking issues for the...
  20. Ranglin5o

    Robert's 210 no expenses spared build

    Got the tank setup and perfectly leveled to 1/32" water line different at the top. Process took 5 days for the RO water to fill the system
Top